Operation and Maintenance During the Break-In Period of Cranes
Author: Dongpu Lifting Machinery
After a crane leaves the factory, it typically undergoes a break-in period of approximately 60 hours—sometimes referred to as a running-in period—which is specified by the manufacturer based on the equipment’s technical characteristics during its initial phase of use. This break-in period is a critical stage for ensuring the crane operates smoothly, reducing the failure rate, and extending its service life.
After a crane leaves the factory, it typically undergoes a break-in period of approximately 60 hours—sometimes referred to as a running-in phase—which is established by the manufacturer based on the equipment’s technical characteristics during its initial operating stage. This break-in period is a critical phase for ensuring the crane operates smoothly, reducing failure rates, and extending its service life. However, at present, some users, either due to a lack of basic knowledge about crane operation, tight project schedules, or an eagerness to realize returns quickly, overlook the specific technical requirements of this initial period. Some even assume that, since the manufacturer provides a warranty, any breakdown will be covered by repairs, leading them to operate the machine under excessive load for extended periods during the break-in phase. As a result, premature failures become frequent, not only disrupting normal use and shortening the crane’s service life but also delaying project progress due to equipment malfunctions. Therefore, proper attention must be paid to the operation and maintenance of cranes during their break-in period.
I. Characteristics of the Break-in Period:
1. Fast wear rate
Due to factors such as the machining, assembly, and adjustment of new machine components, the friction surfaces are rough, the contact area between mating surfaces is small, and the pressure distribution across the surfaces is uneven. During operation, the irregularities on the component surfaces interlock and rub against each other; the metal debris worn off further acts as an abrasive, continuing to participate in the friction process and accelerating wear on the mating surfaces. Consequently, during the break-in period, components—especially their mating surfaces—are prone to rapid wear. If the machine is operated under overload conditions at this stage, it may lead to component damage and premature failure.
2. Poor lubrication
Because the mating clearances of newly assembled components are relatively small, and due to assembly factors, it is difficult to ensure uniform clearance distribution. Consequently, lubricating oil or grease struggles to form a consistent lubricant film on the friction surfaces, failing to adequately prevent wear. This reduces lubrication efficiency and can lead to premature, abnormal wear of machine parts. In severe cases, it may cause scoring or galling on precision‑fit friction surfaces, ultimately resulting in equipment failure.
3. Loosening occurs
Newly manufactured and assembled components often exhibit deviations in geometric shape and fit dimensions. During the initial period of operation, under the influence of alternating loads such as impact and vibration, as well as thermal effects and deformation, coupled with excessively rapid wear, these components—originally fastened tightly—tend to loosen.
4. Leakage occurs
Due to component looseness, vibration, and thermal expansion of the machinery, leakage may occur at sealing surfaces and pipe joints. Additionally, certain casting or machining defects that are difficult to detect during assembly and commissioning can be revealed by the vibrations and impacts experienced during operation, manifesting as oil or water leaks. Consequently, leakage is particularly common during the break-in period.
5. Frequent operational errors
Due to insufficient understanding of the machine’s structure and performance—particularly among new operators—operational errors can easily lead to malfunctions and even mechanical accidents.
II. Use and Maintenance During the Break-In Period
1. As cranes are specialized vehicles, operators must undergo training and guidance provided by the manufacturer, gain a thorough understanding of the machine’s structure and performance, and acquire adequate operational and maintenance experience before operating it. The product operation and maintenance manual supplied by the manufacturer is essential reference material for equipment operation; prior to operating the machine, operators must carefully read this manual and perform operations and maintenance in accordance with its instructions.
2. Pay attention to the operating load during the break-in period; generally, do not exceed 80% of the rated load, and schedule an appropriate workload to prevent overheating caused by prolonged continuous operation.
3. Regularly monitor all instrument readings; if any abnormalities are detected, stop the machine immediately and address the issue. Do not resume operation until the cause has been identified and the fault has been rectified.
4. Regularly check the levels and quality of lubricating oil, hydraulic fluid, coolant, brake fluid, and fuel (including water content), and ensure the machine’s overall sealing is intact. If excessive oil or fluid loss is detected during inspection, investigate the underlying cause. In addition, reinforce lubrication at all designated points; during the break-in period, it is recommended to grease these points at each shift (unless otherwise specified).
5. Keep the machine clean, and promptly adjust and tighten any loose components to prevent increased wear or loss of parts caused by looseness.
6. Once the break-in period is over, perform a mandatory maintenance check on the machine, carry out thorough inspections and adjustments, and be sure to replace the lubricants.
In summary, the maintenance requirements for cranes during their break-in period can be distilled into four key principles: enhanced training, reduced load, meticulous inspections, and rigorous lubrication. By giving due attention to and strictly adhering to these guidelines, you can minimize early‑stage failures, extend the equipment’s service life, boost operational efficiency, and ultimately maximize the return on your investment.
Latest News
What are the main load-bearing mechanisms of lifting machinery?
Construction machinery is evolving toward greater environmental sustainability and digitalization.